(770) 452-1545

    5461 Peachtree Road
    Chamblee, GA 30341

    Mon. thru Fri., 11AM - 6PM
    Sat. 10AM - 6PM
    Sun. 1PM - 5PM
Home :: Blog


Welcome to the CFD Blog

Check this link for timely information and helpful hints from our staff, as well as specialized information from our many friends and business partners of the Depot. We will continually refine our website to allows us to better communicate with our community of shoppers and consignors.

Our first posting comes from Alan Noel, our go-to guy when it comes to wood. Alan operates NOEL'S WOODWORX nearby at 5105-E Peachtree Industrial Blvd and can be reached at 770-936-0667 and at anoelfurniture@bellsouith.net Tis the season... and Alan gives some helpful hints for when things get too jolly on your furniture finishes...

The Party's Over

Before we move on to the hard stuff, let's start with another tricky threat to your furniture. A call that I get very often after the holidays is "How do I get candle wax off my prized antique piece of furniture?" or "I have a spot on my table that won't go away". Fortunately, minor damage can often be treated without too much trouble. Below are a few simple tips for repairing common blemishes in wood furniture. However, if your piece is particularly valuable or the damage is severe, you may want to consult a furniture restoration specialist before attempting these or other repairs.


A simple and easy way to remove wax is to apply mineral spirits with a soft rag and rub gently until the wax is completely dissolved. It can then be wiped off with a clean soft cloth. After this a cloth with a little soapy water should be used to clean off the residue, and then the surface should be wiped clean with a dry soft cloth.


Alcoholic beverages, on the other hand, pose an entirely different problem when left to dry on a finished surface. Since alcohol dries at such a fast rate it creates a great deal of heat. The effect this has on lacquer and varnish finishes is usually a "fume spot" where the finish appears very dull and flat. To bring the shine back it generally takes a little wet sanding with a special type of sandpaper known as "wet-dry" sandpaper. 3M Imperial™ WetorDry™ sandpaper is available in super-fine grits from 1000-2500 that are great for rubbing out or polishing finishes.

This type of paper is made of smooth-cutting silicon carbide and is used wet with soapy water or mineral spirits as a lubricant. It will make very quick work of sanding the finish, so go easy. Be sure to sand in the direction of the wood grain. After a light sanding the finish can then be polished back to its original luster using a polishing compound such as Behlen Rottenstone mixed with any paste wax, or Meguiar's Swirl Remover.

If the overall finish has a satin or dull appearance, use #0000 steel wool or a white Scotch-Brite pad after sanding to rub out the area to match the existing finish. However, never attempt to bring a gloss finish back to its original polished sheen using this method, as even the finest steel wool will scratch too deeply for polishing compounds to rub out the scratches on the surface. On glossy surfaces it is best to use a polishing compound with a high-speed rotary buffer.

If the finish happens to be shellac, the alcohol will have melted the finish and probably created quite a mess. If this is the case, then the finish has to be wet-sanded flat and more shellac applied either by brush or using the French polishing method.

Water Spots or Rings:

White spots or rings caused by water are sometimes easy to remove if they are very close to the surface. White spots are caused when gravity pulls the water into the porous surface and evaporates into a cloud you then see as a white spot or ring. If the damage is close to the surface, a light heating with a hair dryer THAT IS CONSTANTLY MOVING BACK AND FORTH and held at least 12 inches away from the surface may expand the finish enough to release the cloud. Don't use too much heat, or it may bubble the finish.

If this doesn't do the trick, the next method would be to apply petroleum jelly (Vaseline) to the spot and let it sit for at least 12 hours. Wipe this off with a soft cloth lightly dampened with mineral spirits, and then wipe dry with a clean soft cloth.

Liberon Ring Remover will also remove most white water spots and rings as well as heat marks on most highly polished surfaces including French polishes, lacquers, varnishes and other modern hard finishes.


  • Old flannel or terry cloth is very good for cleaning finishes.
  • Never try to "scrape away" (with a fingernail, credit card, etc.) anything on a finished surface.
  • Finishes allow liquid to pass through since the substrate has to expand and contract with the changing barometric pressure and fluctuating temperatures. The finish has no choice but to try and move along with the substrate and since the substrate is much more massive and moves farther than the finish can, the finish cracks. This "alligatoring" or cracking is microscopic and can't be seen by the naked eye until the surface has expanded and contracted over a long period of time.
  • All surface films will eventually crack. Paste wax is the only treatment that will "clog" the porous areas of the finish and help keep moisture out and any damages due to spills and abrasions to a minimum.
  • If any repair seems to be beyond your expertise then it is advisable to consult a professional, as you may inadvertently cause even more damage to the surface if you attempt to repair it.
  • As for burns, they are some of the most difficult blemishes to repair; therefore, it is best to call a furniture restoration specialist for this type of damage.